This is the most current price list, however due to market instability in raw materials, prices are subject to change.    For the most updated price, you will need to call for quotes.   

If you don’t see the part you are looking for here, give us a call at 636-209-4787 or 636-359-0588 or send us an email at sales@trcind.com. 

 

We speak both English and Spanish!  Hablamos Ingles y Español! 

We don’t have all of out parts listed here….there are a lot of them!!

Hot Cutter Parts

Note: HC4 designates parts for a 4 1/2″ cutter, HC7 designates parts for a 7″ cutter. 

HC-4	Air Valve	$     93.00
HC4-1	Linear Motion Block	$   108.50
HC4-2	4 1/2″ Hot Knife Blade Carrier	$     84.00
HC4-3	4 1/2″ Heating Block	$     125.00
HC4-4	Hot Knife Blade	$     25.00
HC4-5	Cutting plate	$    118.50
HC4-6	4 1/2″ Heat Shield	$     32.00
HC4-8	4 1/2″ Heating Element	$     97.00
HC4-9	Heater Terminal Block	$     12.75
HC4-10	Heater Cord	$     25.50
HC7-3	7″ Heating Block	$   150.00
HC7-4	7″ Hot Knife Blade	$     25.00
HC7-5	7″ Cutting Plate	$     80.25
HC7-6	Heat Shield	$     38.50
HC7-8A*	Heating Element (7″ machine uses 2)	$     89.00

*In the past, two different heating element parts were available for the 7″ hot cutters – a long and a short side. These were referred to as HC7-8A and HC7-8B. We have switched to using two of the same heating elements for the 7″ machine, rather than two different heaters. 

Cold Cutter Parts

Note: CC4 designates 4 1/2″ cutter parts, CC7 designates 7″ cutter parts

CC-4	CC Air Valve	$     93.00
CC4-1	CC4 Knife Box	$   255.00
CC4-2	4 1/2″ Top Blade Carrier Block	$     89.75
CC4-3	4 1/2″ Cold Cutter Top Blade-Top Blade	$   191.50
CC4-5	4 1/2″ Cold Cutter Bottom Blade-	$   191.50
CC-5	Cold Cutter Air Cylinder	$    118.50
CC7-3	7″ Cold Cutter Top Blade-	$   223.50
CC7-5	7″ Cold Cutter Bottom Blade	$   223.50
CC-9	Cold Cutter Flow Control-	$     33.00

All Machine Parts

AM-1L	Spring Arm Left Side	$     35
AM-1R	Spring Arm Right Side	$     35
AM4-6A	4 1/2″ Top Roller Assembly	$   175
AM4-6A/A	4 1/2″ Aluminum Top Roller Assembly (knurling is an additional cost)	$     220
AM4-7A	4 1/2″ Rubber Bottom Roller Assembly 4 1/2″	$   175
AM4-7A/A	4 1/2″ Aluminum Bottom Roller Assembly (knurling is an additional cost)	$     220
AM7-1	7″ Base Plate	$     75.00
AM7-5	7″ Guard Plate	$   25.50
AM7-6A	Rubber Top Roller Assembly 7″	$    190
AM7-7A	Rubber Bottom Roller Assembly 7″	$    190
AM7-6A/A	7″ Smooth aluminum top roller	$   230
AM7-7A/A	7″ knurled aluminum bottom roller	$    275
AM-8	Bottom roller bearing	$     25.50
AM-9	Top roller bearing-	$     25.50
AM-10	Lift shaft bushing	$     10
AM-11	Bushing Bulk Head-	$     10
AM-12	Swivel Male Elbow	$     10
AM-13	Male Elbow	$     10
AM-13C	90 degree elbow	$     10
AM-14	1/4″ Bulkhead Fitting	$     12.75
AM-15	Straight push in air fitting	$       10
AM-16	1/4″T x 1/4″P Straight Male Connector	$       8.75
AM-18	CS/VS Drive Motor-	$   223.50
AM-21-12	12 tooth, 1/4″ ID Motor Pulley-	$     25.50
AM-22-15	25 tooth, 1/2″ ID Bottom Roller Pulley	$     25.50
AM-23-65	65 Tooth Drive Belt	$     19.25
AM-24	Pulley Guard	$     38.50
AM-25	Linear Shaft 4″ long 1/2″ diam.-1/2″ x 4″	$     16.00
AM-26	Linear Bushing	$     27.50
AM-27	1/2″ diam. Linear ball bearing	$     65.00

Alternating Angle Parts

AA-8	Air Cylinder Mount	$     83.00
AA-10	Heating Block-Hot Cutter	$   115.25
AA-11	Hot Knife Blade	$     25.50
AA-16	Rotating Drive Shaft	$   75.00
AA-17	Heating Element	$   85
AA-18	Air Cylinder	$   83

Circuit Board Parts

CB-KEYPAD

Keypad 4 x 1 (1 row)

$     24.95

Cutoff Switch Parts

CO-6

Micro Switch-

$       9.50

Control Panel Parts

CP-4	Power Switch	$     12.50
CP-5	Fused Power Receptacle-	$     32.00
CP-7	Thermostat	$     85.00
CP-8	Heater Cord Receptacle	$     12.75
CP-14-3	DB-15 Hood	$       6.50
CP-14A	Control Cable Assembly	$     55.00
CP-15-VS	Variable Speed Drive Board	$   961.75
CP-15-VSAA	Alternating Angle Circuit Board	$    1275
CP-18	Panel Mount Fuse Holder-	$     12.75